K.334 - RESINA X BASE COAT PASTELLI

FIELD OF APPLICATION:

For general-purpose double-layer painting, machine tools, agricultural machinery, etc.

For general-purpose double-layer painting, machine tools, agricultural machinery, etc.

RECOMMENDED PRIMERS:

See in substrate preparation

PREPARATION OF THE SUBSTRATE:

Iron surfaces: Remove any traces of rust, grease, calamine and humidity by means of thorough mechanical cleaning, followed by degreasing. Apply a coat of our SINTOFLEX - 494 or 490 series. After 6-12 hours apply fast drying enamel. Aluminum: Sanding followed by degreasing with organic solvents. Apply a coat of epoxy primer 193 or 190, or acrylic 793. Galvanized sheet: Buffing or sanding followed by degreasing with organic solvents. Apply a coat of epoxy primer 193 or 190, or acrylic 793.

Iron surfaces: Remove any traces of rust, grease, calamine and humidity by means of thorough mechanical cleaning, followed by degreasing. Apply a coat of our SINTOFLEX - 494 or 490 series. After 6-12 hours apply fast drying enamel. Aluminum: Sanding followed by degreasing with organic solvents. Apply a coat of epoxy primer 193 or 190, or acrylic 793. Galvanized sheet: Buffing or sanding followed by degreasing with organic solvents. Apply a coat of epoxy primer 193 or 190, or acrylic 793.

PREPARATION OF THE PRODUCT:

In the absence of a stirrer, the following procedure should be followed to ensure complete dispersion: 1. Dose the coloring pastes (including neutral, if any) into a container as listed in the Colortech formulation; 2. Thoroughly mix the pastes, even by hand, until a uniform color is achieved; 3. Add the converter to the paste mixture just prepared (or add the pre-mixed pastes to the pre-weighed converter) and immediately mix again Comp. A: K.334 + Coloring Pastes 100 parts by weight or volume Diluent (1): D.737 or D.747 40 – 60 parts by weight or volume

PRODUCT SPECIFICATIONS:

PREPARATION OF THE PRODUCT:

In the absence of a stirrer, the following procedure should be followed to ensure complete dispersion: 1. Dose the coloring pastes (including neutral, if any) into a container as listed in the Colortech formulation; 2. Thoroughly mix the pastes, even by hand, until a uniform color is achieved; 3. Add the converter to the paste mixture just prepared (or add the pre-mixed pastes to the pre-weighed converter) and immediately mix again Comp. A: K.334 + Coloring Pastes 100 parts by weight or volume Diluent (1): D.737 or D.747 40 – 60 parts by weight or volume

TYPE OF PRODUCT:

Single-component.

PRODUCT SPECIFICATIONS:

APPEARANCE OF THE FILM:

Semi-matte

TYPE OF PRODUCT:

Base Coat

COLORS:

By choice

APPEARANCE:

Semi-matte

DENSITY:

0,98 Kg/L (± 0,10)

COLORS:

By choice

SUPPLY VISCOSITY:

14(+-3) DIN 8 at 20 °C

DENSITY:

0,98 Kg/L (± 0,10)

SOLID CONTENT:

36% (± 2%)

SUPPLY VISCOSITY:

14”(+-3) DIN 8 at 20 °C SOLID % - VOLUME 31% (± 2%) SOLID % - WEIGHT 36% (± 2%)

DRYING AT 20° C:

Dust-free: 10 - 15’   Print-free: 1 - 2 hours

Dust-free: 10 - 15’   Touch-free: 1 - 2 hours

RECOMMENDED LAYERS:

2 - 3

2 - 3

RECOMMENDED THICKNESS:

25 - 30 microns

RECOMMENDED – DFT:

25 - 30 microns

THEORETICAL YIELD (*):

11,8 m2/Lt or 10,2 m2/Kg at 25 micron dry

9,8 m2/Lt or 9,3 m2/Kg at 30 µm dry

RECOATING:

20 - 30 minutes at 20 °C

20 - 30 minutes at 20 °C

RECOMMENDED OVERCOATS:

701.HS010 - 701.HS050 - 701.HS060 - 701.HS100 701.00015 - 704.00020 (*) In 80/20 ratio with P.900

701.HS010 - 701.HS050 - 701.HS060 - 701.HS100 701.00015 - 704.00020 (*) In 80/20 ratio with P.900

SAFETY REGULATIONS:

Strictly follow the instructions on the labeling and in the safety data sheet.

APPLICATION INSTRUCTIONS:

View pictograms Page 1.

SAFETY REGULATIONS:

Strictly follow the instructions on the labeling and in the safety data sheet.

STORAGE CONDITIONS:

The storage room must be dry and with a temperature between +10 °C and +35 °C. Rev.: 03/22 The data and information contained in this sheet are the result of our experience and accurate laboratory tests. However, since the painting process represents a set of operations that are beyond our control, they do not therefore guarantee, in any way, the final performance of the cycle.

The storage room must be dry and with a temperature between +10 °C and +35 °C. Rev.: 09/24 The data and information contained in this sheet are the result of our experience and accurate laboratory tests. However, since the painting process represents a set of operations that are beyond our control, they do not therefore guarantee, in any way, the final performance of the cycle.

The data and information contained in this sheet are the result of our experience and accurate tests and laboratory tests.
However, since the painting process is a set of operations that are beyond our control, they therefore do not constitute, in any way any form of guarantee on the final performance of the cycle itself.