Developed for high-thickness, single-coat direct applications on various types of metals, such as bare sheet metal, galvanized sheet metal, and aluminum. Excellent outdoor resistance and anti-corrosion characteristics.
High-quality finish, particularly suitable for direct painting of metal substrates intended for both interior and exterior use.
Iron and steel sheet metal: Sandblasting grade Sa 2.5 (max. roughness 30µ), or careful sanding with suitable abrasive (P.80 - P.120) followed by degreasing with solvent. Galvanized sheet: Scouring with Scotch Brite followed by degreasing with solvents. Aluminum and light alloys: Sanding with P.280 - 320 followed by degreasing with solvents.
Comp. A: K.732 + Coloring Pastes 100 parts by weight (Ratio 80/20 with paste P.) Comp. B: CZ.711 (1) Standard 20 parts by weight CZ.720 Fast (Operating T° <20 °C) 20 parts by weight Or: CZ.221 (2) 15 parts by weight Diluent: D.737 or D.219 5 - 15 parts by weight (1) With these application methods, the product, which according to VOC regulations (Directive 2004/42/CE) belongs to the category: “Two-component high performance paints” with a max. limit of 500 gr/lt, has a VOC in the ready-to-use product of about 470 gr/lt. (2) With Airless or mixed air application modes, CZ.221 can be used and catalyzed at high usual and a maximum dilution of 5 percent, resulting in a ready-to-use VOC of less than 420 gr/lt. Use CZ.221 only on sandblasted steel. After adding the pastes and mixing them perfectly, catalyze according to the recommended ratios, then mix thoroughly until uniform color and consistency. Dilute with our D.737 or D.219 up to the desired viscosity.
Two-component;
Semigloss
By choice
1,49 kg/lt (± 0,05)
24" (± 3") Ford 8 at 25 °C
77% (± 2%)
Dry dust-free - Print-free: 4-5 hours. 10’ - 15’ at 20 °C - Dry to touch - Print-free: 4-5 hours. 3 hours (3) - Forced Drying - Print-free: 4-5 hours. 45’ - 60’ at 60 °C
2 - 3 coats
85 Gloss (± 5) depending on the color and thickness applied
80 - 130 µm
2 - 3 hours. The pot-life decreases at higher temperatures
5,6 m2/lt or 4 m2/kg at 100 µm dry (3) 50 - 60 µm with catalyst CZ.711 Standard (4) In 80/20 ratio with our P.900
K.732 and K.734 can be mixed in any ratio to achieve the desired opacity, as per the table below:
GLOSS (Gloss at 60 °C RAL 7035) K.734 10 ±2 5 : 1 18 ±2 3 : 1 25 ±2 1 : 1 50 ±3 1 : 2 70 ±4 K.732 85 ±5
Wet-on-wet within 12 hours. After complete curing of the film, it is necessary to sand lightly before painting.
Strictly follow the instructions on the labeling and in the safety data sheet.
The storage room must be dry and with a temperature between +10 °C and +35 °C. Rev.: 06/22 The data and information contained in this sheet are the result of our experience and accurate laboratory tests. However, since the painting process represents a set of operations that are beyond our control, they do not therefore guarantee, in any way, the final performance of the cycle.
The data and information contained in this sheet are the result of our experience and accurate tests and laboratory tests.
However, since the painting process is a set of operations that are beyond our control, they therefore do not constitute, in any way any form of guarantee on the final performance of the cycle itself.
P.010
NEUTRAL PASTE
P.100
BLACK DYES PASTE
P.106
DEEP BLACK PASTE
P.110
OXIDE YELLOW PASTE
P.115E
ECO LEMON YELLOW PASTE
P.116
COVERING ECO LEMON YELLOW PASTE
P.119E
ECO MEDIUM YELLOW PASTE
P.200E
ECO ORANGE PASTE
P.323
BRIGHT RED PASTE
P.325
DARK RED PASTE
P.330
OXIDE RED PASTE
P.354
SOLID RED PASTE
P.400
VIOLET PASTE
P.500
BLUE PASTE
P.600
GREEN PASTE
P.701
FINE ALUMINIUM PASTE
P.703
MAGNUM ALUMINIUM PASTE
P.900
WHITE PASTE
P.250
BRILLANT ORANGE ECO
P.562
LIGHT BLUE PASTE
TP.150
BLACK PASTE
TP.156
DEEP BLACK PASTE
P.TX050
FINE-GRAINED TEXTURE PASTE
P.TX70
MEDIUM-GRAINED TEXTURE PASTE
P.TX80
COARSE-GRAINED TEXTURE
P.TX90
EXTRA COARSE-GRAINED TEXTURE PASTE
P.F115
FLUORESCENT YELLOW PASTE
P.F200
FLUORESCENT ORANGE PASTE
P.F300
FLUORESCENT RED PASTE
P.F400
FLUORESCENT PINK PASTE
P.F500
FLUORESCENT BLUE PASTE
P.F600
FLUORESCENT GREEN PASTE
P.700
FINE-GRAINED ALUMINIUM PASTE
P.710
SHINY FINE-GRAINED ALUMINIUM PASTE
P.715
FINE MEDIUM-GRAINED ALUMINIUM PASTE
P.716
LIGHT COLOUR MEDIUM-GRAINED ALUMINIUM PASTE
P.720
SHINY MEDIUM-GRAINED ALUMINIUM PASTE
P.730
SHINY MAGNUM-GRAINED ALUMINIUM PASTE
P.733
COARSE-GRAINED ALUMINIUM PASTE
P.739
MAGNUM MEGA-GRAINED ALUMINIUM
P.740
LUMINOR ALUMINIUM PASTE
P.755
EXTRA-FINE ALUMINIUM PASTE
P.758
ULTRA-FINE ALUMINIUM PASTE
P.769
FINE-GRAINED ALUMINIUM PASTE
P.801
PEARLY MEDIUM PASTE
P.803
PEARLY MEDIUM WHITE EXTRA
P.805
PEARLY SHOT GOLD PASTE
P.811
PEARLY FINE PASTE
P.812
PEARLY MAGNUM PASTE
P.813
PEARLY WHITE REFLECTIVE
P.814
PEARLY MEGA MAGNUM PASTE
P.815
PEARLY SHOT RED
P.819
PEARLY SHOT LILAC
P.825
PEARLY SHOT BLUE
P.830
PEARLY GOLD PASTE
P.835
PEARLY SHOT GREEN PASTE
P.836
PEARLY GOLD OLYMPIC PASTE
P.840
PEARLY SHOT VIOLET
P.850
PEARLY BRONZE PASTE
P.851
PEARLY BRIGHT RED
P.852
PEARLY COPPER RED
P.853
PEARLY MAGNUM RED
P.854
PEARLY RED PASTE
P.866
DARK COPPER PASTE
K.232
POLIURETANICO IN.LE SEMILUCIDO
TP.016
CLEAR OXIDE YELLOW PASTE
TP.037
CLEAR OXIDE RED PASTE
TP.065
CLEAR OXIDE RED PASTE
TP.066
CLEAR OXIDE YELLOW PASTE
TP.110
OXIDE YELLOW (EX TP.111)
TP.115
LEMON YELLOW (EX TP.102)
TP.116
COVERING LEMON YELLOW (EX TP.122)
TP.119
MEDIUM YELLOW (EX TP.114)
TP.200
ORANGE (EX TP.220)
TP.323
BRIGHT RED (EX TP.370)
TP.325
DARK RED (EX TP.321)
TP.330
OXIDE RED (EX TP.300)
TP.354
SOLIDE RED (EX TP.329)
TP.400
VIOLET (EX TP.440)
TP.500
BLUE (EX TP.510)
TP.600
GREEN (EX TP.607)
TP.900
WHITE (EX 40610)
VERNICI CALDART SRL © 2022 | P.IVA IT00759630965 | Privacy Policy | Cookies Policy | Ethical Code | Whistleblowing | Financing | SOFTWEB