Suitable for application on steel, aluminum, galvanized and plastics. Metal, previously degreased, sanded and cleaned If necessary, on particular plastics or metals, apply suitable primer beforehand. Steel sanding with P120 grit. Aluminum sanding with P150 or P180 grit. Galvanized steel: sanding with P240 grit. Old paintwork not sensitive to solvents sanding with P240 grit. However, it is recommended that prior testing be carried out to assess its actual suitability for the material to be painted.
Mix well before use; the product is ready to use. Supply viscosity approx. 15" cup ASTM4 at 20 °C The product is semi-covering and should NOT be applied to full coverage. Do not exceed 120 µm wet on metal and 70 µm wet on plastic. Always achieve the desired thickness with blurred application. Higher thicknesses will necessarily have to be matched by longer flash off time, both between coats during application and before UV curing.
For flash off in environments with temperature below 18 °C, it is recommended to use a heat gun at 40/60 °C or IR lamps for a few minutes before UV curing.
UV single-component
Semi-matte
Gray
About 1,15 Kg/l (± 0,05)
14” - 15” ASTM 4 at 20 °C
70% - 72%
Irradiance > 25 mW/cm2 (*) UV - A (LED): 365 – 405 nm UV dose> 1000 mJ/cm² (*)
60 - 120 µm wet
dry P400 - P500
wet P800 (*) Tesla Cure at 10cm for 100 sec, referring to an average surface of size 30 cm x 30 cm; Measurement made with MICROCURE EIT (UV-A). Increase the irradiation time in proportion to the size of the painted area. The irradiation time required to achieve complete and proper curing depends on the surface to be covered, the thickness applied, the distance of the lamp, and the characteristics of the lamp such as power and emission spectrum.
Strictly follow the instructions on the labeling and in the safety data sheet.
In unopened and sealed packages, kept at a temperature of +5 to +30 °C. Rev.: 03/22 The data and information contained in this sheet are the result of our experience and accurate laboratory tests. However, since the painting process represents a set of operations that are beyond our control, they do not therefore guarantee, in any way, the final performance of the cycle.
The data and information contained in this sheet are the result of our experience and accurate tests and laboratory tests.
However, since the painting process is a set of operations that are beyond our control, they therefore do not constitute, in any way any form of guarantee on the final performance of the cycle itself.
7H1.F0210
ELITE UHS
7H1.F0249
ELITE UHS
7H1.F0601
ELITE UHS
7H1.F268/A
ELITE UHS
7H1.F296/A
ELITE UHS
7H1.IC194
ELITE UHS
7H1.R369
ELITE UHS RENAULT 369 BLANC GLACIER
374.00199
BC TOYOTA 199 - SILVER
374.040
BC TOYOTA 040 - SUPER WHITE
374.1E0
BC TOYOTA 1E0 - DARK GREY MICA
374.2431
BC FORD 6.1/2431 - MONDUST SILVER
374.2851
BC FORD 2851 - BLACK PANTHER
374.BMW354
BC BMW 354 - MET. TITANSILBER
374.D69
BC RENAULT D69 - GRIS PLATINE
374.DB744
BC DB.744 - BRILLANT SILVER
374.DB761
BC DB.761 - MET. POLARISSILBER
374.EZR
BC CITROEN EZR - GRIS ALLUM.
374.F0249
BC FIAT 249/96 - WHITE
374.F0348
BC FIAT 348 - MET. SILVER GREY
374.F0589A
BC FIAT 589/A - DEEP SILVER GREY
374.F0595A
BC FIAT 595/A - FLAWLESS GREY
374.F0601
BC FIAT 601 - BLACK
374.F0602A
BC FIAT 602/A - ALUMINIUM
374.F0612A
BC FIAT 612/A - ELISA GREY
374.F0632
BC FIAT 632 - MET. BLACK
374.F0647F
BC FIAT - FINE-GRAINED STEEL GREY
374.F0647G
BC FIAT - COARSE-GRAINED STEEL GREY
374.F0695
BC FIAT 695 GREY MET
374.F0891B
BC FIAT 891/B - MET. PROVOCATIVE BLACK
374.F268/A
BC FIAT 268/A - SUPER WHITE
374.F296/A
BC FIAT 296 - WHITE
374.F565/A
BC FIAT 565/A - MET. ALLEGRO GREY
374.F599/A
BC FIAT 599/A - MET. MAGNETIC BLUE
374.F876/B
BC FIAT 876/B - MET. CARBON BLACK
374.GM157
BC OPEL - STARSILBER LII MET. GREY
374.LC9Z
BC VOLKSWAGEN LC9Z - PEARL BLACK
374.LY7W
BC VOLKSWAGEN - MET. LICHTSILBER
374.LY9C
BC VOLKSWAGEN LY9C - IBISWEISS
374.R369
BC RENAULT 369 - BLANC GLACIER
374.R676
BC RENAULT 676 - NOIR NACRE
374.VWA7W
BC VOLKSWAGEN A7W - REFLEXSILBER
D.040
Blending Thinner
D.721
Thinner for base coat
D.727
SLOW
D.737
STANDARD
D.747
FAST
CZ.105
EPODUR STANDARD
CZ.700
ACRYDUR HS
CZ.711
ACRYDUR HS
CZ.720
ACRYDUR HS
CZ.750
ACRYDUS UHS
CZ.760
ACRYDUR UHS
CZ.761
ACRYDUR
CZ.770
ACRYDUR UHS
CZ.771
ACRYDUR
CZ.781
ACRYDUR
VERNICI CALDART SRL © 2022 | P.IVA IT00759630965 | Privacy Policy | Cookies Policy | Ethical Code | Whistleblowing | Financing | SOFTWEB