794.70065 - EUROFILLER HS - FONDO 5:1 GRIGIO SCURO

NATURE AND PRODUCT FEATURES:

The 5:1 acrylic two-component primer 794.70065 is a high-fill insulating primer characterized by ease and versatility of use. Distinguished by excellent spreading and casting resistance, fast curing and easy sanding. Absence of sagging and/or marks; can be used for both touch-ups and total renovations. Applicable to properly prepared polyester putties, fiberglass, old two-component paints (still adhering and intact).

FIELD OF APPLICATION:

Can be used as an insulating, filling and highly filling primer depending on the requirements and application scheme used. There are three different types of hardeners to complete the product: Standard, Slow and Fast to be used depending on the working temperature and/or size of the workpiece to be painted.

PREPARATION OF THE PRODUCT:

Thoroughly mix component A until the color and consistency are uniform. Then mix with component B in the ratio shown below: Component Blend by volume Blend by weight Primer 794.70065 5 100 Hardener CZ.711 (*) Standard 1 13 Diluent D.737 (*) Standard 1-1,3 15-20 (*) Hardener and thinner should be chosen according to environmental conditions and the size of the piece. Dilute the perfectly blended mixture with 15-20% of our polyacrylic thinners until obtaining the best viscosity for the desired effect. Room temperature +15 °C to +25 °C Most applications are made under such conditions. Use Standard hardener and thinner; Room temperature +5°C to +15 °C In this case and particularly for small parts or touch-ups use CZ.720 rapid hardener and Standard thinner; Room temperature +25 °C to +35 °C Prevent the product from drying too quickly by originating bad distension and too many spray fumes. Slow down the drying time of the film by using slow thinner D.727. If the size of the piece is particularly large (e.g., complete painting of a vehicle) also use the slow hardener CZ.700. We do not recommend using the product as highly filler in this case. Application diagrams (Referred to temperature conditions of 20 °C) Application data Insulator Filler Highly filler Dilution (by weight) 15-20 13-15 13 Gravity Feed nozzle 1.4-1,8 1.4-1.8 1.8 Number of coats 2-3 2-3 3-4 Interval between coats 8-10 minutes 8-10 minutes 10 minutes Recommended thickness 100-125 µm 125-150 µm 150-200 µm Pot-life 50 minutes 50 minutes 45 minutes Curing at A.T. 5 hours 5-6 hours 6-8 hours Curing in furnace 45 minutes at 60 °C 50 minutes at 60 °C Not recommended IR medium wave curing 10 minutes 10 minutes Not recommended

PRODUCT SPECIFICATIONS:

TYPE OF PRODUCT

Two-component;

APPEARANCE OF THE FILM

Matte.

COLORS

Dark gray

SPECIFIC WEIGHT

1,65 Kg/l (± 0,05)

SUPPLY VISCOSITY

Thixotropic Product

DRY RESIDUE (A)

78% (± 2%) V.O.C. 2004/42/CE-IIB (c)(540)540

DRYING

Dry dust-free - Print-free: 4-5 hours. 10’ at 20 °C - 25 °C   Forced Drying 30’ - 40’ at 60 °C - 70 °C (sandable)

RECOMMENDED LAYERS

Two coats

RECOMMENDED THICKNESS

100 - 125 µm

POT-LIFE AT 20 °C

60’. The pot-life decreases at higher temperatures

SAFETY REGULATIONS:

Strictly follow the instructions on the labeling and in the safety data sheet.

STORAGE CONDITIONS:

In unopened and sealed packages, kept at a temperature of +5 to +30 °C. Rev.: 03/22 The data and information contained in this sheet are the result of our experience and accurate laboratory tests. However, since the painting process represents a set of operations that are beyond our control, they do not therefore guarantee, in any way, the final performance of the cycle.

The data and information contained in this sheet are the result of our experience and accurate tests and laboratory tests.
However, since the painting process is a set of operations that are beyond our control, they therefore do not constitute, in any way any form of guarantee on the final performance of the cycle itself.