application datasheet

application datasheet

Download sheet in pdf

KW112 - EPOLAK SEMILUCIDO ALL''ACQUA

View Product Shelf Life

FIELD OF APPLICATION:

Epoxy finish product for general use in industry. Can also be applied to industrial floors, with special resistance to trampling. Applicable directly on iron, aluminum, galvanized iron and light alloys, limited to applications for internal use.

RECOMMENDED PRIMER:

Water-based epoxy or acrylic primers.

PREPARATION OF THE SUBSTRATE:

Water-based paint products, because of their very low organic solvent content, are characterized by poor substrate wettability, which is much less than that of conventional solvent-based products. Therefore, the presence on the substrate of substances, such as grease, oil, grease and dirt (and of course, for other reasons, rust and calamine) is not tolerated. Cleanliness of the substrate is a necessary and fundamental condition so that the outcome of the painting is successful. Iron: SA2 grade sandblasting. Alternatively perfect mechanical cleaning of the substrate by sanding with removal of rust, calamine and subsequent cleaning by degreasing with aqueous solutions or solvents. Galvanized sheet: Thorough buffing or sanding, followed by degreasing with solvents. Aluminum: Mechanical cleaning by sanding, followed by degreasing with solvents. Concrete Floors: On concrete, remove dust and any traces of oil or grease. Concrete surfaces built at least four weeks ago: Always check residual moisture content (? 3% by weight) before painting. Moisture could also rise from the base by capillarity. Perform, the "plastic sheet test" (2m x 2m polyethylene sheet taped to the concrete surface to be painted). The sheet must remain in place for at least 24 hours, so any rising vapor that would condense on the sheet can be detected. In the case of particularly smooth surfaces (resulting from finishing treatments, for example, with a concrete helicopter), it is recommended to roughen (with processes such as grinding, sanding, sandpapering, etc.) and eliminate any kind of contamination (fats, oils, acids, cracks, cavities, etc.) that may preclude or affect paint adhesion.

PREPARATION OF THE PRODUCT:

Comp. A: KW112 + Water-based Tinters – PW 100 parts by weight Comp. B: CZW140 50 parts by weight Before mixing Component A and Component B, it is recommended to mix them well individually and then thoroughly mix the two components together. For applications on concrete, proceed with the first coat well thinned so that it penetrates well into the pores of the concrete. After 3 to 4 hours maximum proceed with the second, thicker coat to cover.

PRODUCT SPECIFICATIONS:

TYPE OF PRODUCT

Epoxy finish WB

APPEARANCE

Semigloss

COLOUR

On request

SPECIFIC WEIGHT (Comp.A)

1,35 Kg/l (± 0,05)

SUPPLY VISCOSITY

Thixotropic SOLID % - VOLUME (A+B) 38% (± 2) SOLID % - WEIGHT (A+B) 53% (± 2)

DRYING TIME AT 20 °C.

Dry dust-free - Print-free: 4-5 hours. 30’   Touch-free 6 - 7 hours   Complete curing 24 - 48 hours   Forced Drying 40’ - 60’ at 60 °C   Maximum chemical resistance after 10 days

RECOMMENDED LAYERS

1 (cross layers) Two coats if applied directly.

RECOMMENDED THICKNESS

40 - 50 µm

THEORETICAL YIELD (1)

7,5 m2/Lt or 5,6 m2/Kg at 50 µm dry

POT-LIFE AT 20 °C

90’. The pot-life decreases at higher temperatures. Under no circumstances should you apply product that has exceeded pot-life limits, as films would not ensure sufficient adhesion and chemical resistance. (1) In 75/25 ratio with PW900. Recommended application environment conditions: Relative humidity 60% - Temp. +10 °C ÷ 30 °C.

APPLICATION INSTRUCTIONS:

View pictograms Page 1.

RECOATING:

After complete drying of the product, minimum after 10 hours and within 36 hours. After 48 hours, light sanding of the film is recommended to ensure good adhesion of the top coat.

SAFETY REGULATIONS:

Water-based products must be protected from frost. Strictly follow the instructions on the labeling and in the safety data sheet.

STORAGE CONDITIONS:

The storage room must be dry and with a temperature between +10 °C and +30 °C. Rev.: 01/24 The data and information contained in this sheet are the result of our experience and accurate laboratory tests. However, since the painting process represents a set of operations that are beyond our control, they do not therefore guarantee, in any way, the final performance of the cycle.

The data and information contained in this sheet are the result of our experience and accurate tests and laboratory tests.
However, since the painting process is a set of operations that are beyond our control, they therefore do not constitute, in any way any form of guarantee on the final performance of the cycle itself.

Other products in TINTOMETRO E PRODOTTI ALL’ACQUA

 > WATER-BASED TINTERS

KW731

WATER-BASED DTM GLOSS ACRYLIC

PW010

NETRUAL WB PASTE

PW050

MATTING AGENT WB PASTE

PW100

BLACK WB PASTE

PW110

OXIDE YELLOW WB PASTE

PW115

LEMON YELLOW WB PASTE

PW119

MEDIUM YELLOW WB PASTE

PW166

DEEP BLACK WB

PW200

ORANGE WB PASTE

PW303

BRIGHT RED WB PASTE

PW305

DARK RED WB PASTE

PW330

OXIDE RED WB PASTE

PW400

VIOLET WB PASTE

PW500

BLUE WB PASTE

PW600

GREEN WB PASTE

PW701

FINE ALUMINIUM WB PASTE

PW703

PASTA ALLUMINIO MAGNUM WB

PW900

WHITE WB PASTE

 > WATER-BASED TEXTURE TINTERS

PWTX50

FINE-GRAINED TEXTURE WB PASTE

PWTX70

MEDIUM-GRAINED TEXTURE WB PASTE

PWTX80

COARSE-GRAINED TEXTURE WB PASTE

PWTX90

EXTRA COARSE-GRAINED TEXTURE WB PASTE

 > WATER-BASED PEARLY TINTERS

PW801

PEARLY MEDIUM WB PASTE

PW805

PEARLY SHOT GOLD WB PASTE

PW825

PEARLY SHOT BLUE WB PASTE

PW836

PEARLY GOLD OLYMPIC WB PASTE

 > WATER-BASED BINDERS

KW111

EPOLAK GLOSS WATER-BASED

Leghe Metallo Vetro

KW162

EPOLAK EMBOSSED SEMI-GLOSS WATER-BASED

Leghe Metallo Vetro

KW193

EPOFLEX WATER-BASED

Leghe Metallo Plastica Vetro

KW374

WATER-BASED BASE COAT BINDER

Plastica

KW431

ONE COAT 1K WATER BASED

Leghe Metallo Vetro

KW494

SINTOFLEX WATER-BASED

Metallo

KW631

WATER-BASED GLOSS BRUSH ENAMEL

Leghe Metallo Vetro

KW634

WATER-BASED MATT BRUSH ENAMEL

Leghe Metallo Vetro

KW644

MICALUX BRUSH WATER-BASED

Leghe Metallo Vetro

KW711

Water-based Extra Gloss Acrylic

KW721

WATER-BASED GLOSS ACRYLIC

Leghe Metallo Plastica Vetro

KW723

WATER-BASED SEMI-GLOSS ACRYLIC

Leghe Metallo Plastica Vetro

KW734

WATER-BASED DTM MATT ACRYLIC

 > WATER-BASED FLUORESCENT TINTERS

PWF115

FLUORESCENT YELLOW PASTE WB

PWF300

FLUORESCENT RED PASTE WB

PWF400

FLUORESCENT PINK PASTE WB

PWF600

FLUORESCENT GREEN PASTE WB