Product for general purpose applications: industrial bodywork, machine tools and/or operating machines, furniture, plastics, etc. The product can also be applied directly without primer to metal substrates, limited to products that are not to be exposed outdoors. For artifacts that are to be exposed outdoors, if high anti-corrosive performance is required, it is recommended that a two-component water-based primer (our 193W70121 or 793.W90900) or solvent-based primer (our 193.R7042) be applied in advance.
Due of their very low organic solvent content, water-based paint products are characterized by poor substrate wettability, which is much less than that of conventional solvent-based products. Therefore, the presence on the substrate of substances such as grease, oil, grease and dirt (and of course, for other reasons, rust and calamine) is not tolerated. Cleanliness of the substrate is a necessary and fundamental condition so that the outcome of the painting is successful. Iron surfaces: Remove all traces of rust, scale, grease and moisture from the substrate by SA2 grade sandblasting or thorough mechanical cleaning followed by solvent degreasing. Apply a coat of two-component waterborne epoxy primer (our 193W70121) or solvent-based (our 193.R7042), water-based acrylic primer (our 793W series). Galvanized surfaces: Scour or sand. Degrease perfectly with organic solvents. Apply one coat of water-based (our 193W70121) or solvent-based (our 193.R7042) two-component epoxy primer. Aluminum: Light sanding followed by degreasing. Apply one coat of water-based (our 193W70121) or solvent-based (our 193.R7042) two-component epoxy primer. The product can also be applied on plastics with direct adhesion. However, a preliminary adhesion test is recommended because of the wide variety of products on the market.
Comp. A: KW711 (75/25 PW) 100 parts by weight Comp. B: czw711 25 parts by weight Or: CZW707 20 parts by weight Thoroughly mix Comp. A until uniform color and consistency. Dose Comp. B and mix the two components well (possibly with low-speed stirrer) before dilution. Dilute successively by adding water to the desired viscosity that best suits the application system, then mix again carefully.
Two-component
Glossy 80 Gloss
On request
1,05 Kg/l (± 0,05)
27” (± 3) DIN 8 AT 20 °C
A+B(1) 53% (± 2)
46% (± 2)
- Dry dust-free - Print-free: 4-5 hours. 20’ - 30’ at 20 °C Print-free 4 - 5 hours at 20 °C in depth 24 - 36 hours at 20 °C Forced Drying 40-50’ at 60 °C Maximum chemical resistance after 14 days
Two single coats Two coats if applied directly.
50 - 80 DFT
5,8 m2/lt or 5,0 m2/Kg a 80 DFT (*) 75/25 WITH PW900
1-2 hours. The pot-life decreases at higher temperatures. Under no circumstances should product that has exceeded pot-life limits be applied as films would be formed that do not give sufficient assurance of adhesion and chemical resistance.
Wet-on-wet or at most after 2-3 hours. When the film is fully cured, light sanding is recommended to ensure good adhesion of the finishing coat.
Strictly follow the instructions on the labeling and in the safety data sheet.
The storage room must be dry and with a temperature between + 10 °C and 35 °C. Rev.: 01/24 The data and information contained in this sheet are the result of our experience and accurate laboratory tests. However, since the painting process represents a set of operations that are beyond our control, they do not therefore guarantee, in any way, the final performance of the cycle.
The data and information contained in this sheet are the result of our experience and accurate tests and laboratory tests.
However, since the painting process is a set of operations that are beyond our control, they therefore do not constitute, in any way any form of guarantee on the final performance of the cycle itself.
PW010
NETRUAL WB PASTE
PW050
MATTING AGENT WB PASTE
PW100
BLACK WB PASTE
PW110
OXIDE YELLOW WB PASTE
PW115
LEMON YELLOW WB PASTE
PW119
MEDIUM YELLOW WB PASTE
PW166
DEEP BLACK WB
PW200
ORANGE WB PASTE
PW303
BRIGHT RED WB PASTE
PW305
DARK RED WB PASTE
PW330
OXIDE RED WB PASTE
PW400
VIOLET WB PASTE
PW500
BLUE WB PASTE
PW600
GREEN WB PASTE
PW701
FINE ALUMINIUM WB PASTE
PW703
PASTA ALLUMINIO MAGNUM WB
PW900
WHITE WB PASTE
PWTX50
FINE-GRAINED TEXTURE WB PASTE
PWTX70
MEDIUM-GRAINED TEXTURE WB PASTE
PWTX80
COARSE-GRAINED TEXTURE WB PASTE
PWTX90
EXTRA COARSE-GRAINED TEXTURE WB PASTE
PW801
PEARLY MEDIUM WB PASTE
PW805
PEARLY SHOT GOLD WB PASTE
PW825
PEARLY SHOT BLUE WB PASTE
PW836
PEARLY GOLD OLYMPIC WB PASTE
PWF115
FLUORESCENT YELLOW PASTE WB
PWF300
FLUORESCENT RED PASTE WB
PWF400
FLUORESCENT PINK PASTE WB
PWF600
FLUORESCENT GREEN PASTE WB
VERNICI CALDART SRL © 2022 | P.IVA IT00759630965 | Privacy Policy | Cookies Policy | Ethical Code | Whistleblowing | Financing | SOFTWEB